Tag Archives: floor finish

Floor and Salt

Don’t Let Winter A-SALT Your Floors

Boots in FrostWinter is in full swing and is taking charge with snow, slush and ice. While bundling up and staying warm inside, make sure you don’t give your floors the cold shoulder. It’s important to be aware of the dangers that the winter elements can leave behind on both carpet and hard surface floors.

As people come and go in a facility they stomp, shake and dump snow, slush and salt on floors everywhere. This snowy, slushy mess doesn’t end after it dries and leaves behind un-melted rock salt. Stains as white as snow can be seen on all types of floor surfaces. While these stains are pesky and damaging, they are preventable and your floors are savable.

Salt stains are not harmful if attended to quickly. The faster you remove the moisture and chemicals, the less time they have to damage your floors. Keep absorbent towels or rags near your doors to clean up the messes as they occur, and a vacuum or broom to remove any dry residue.

Use a reliable matting system. A matting system acts as a first line of defense against tracked-in contaminants on your floors. Over 80% of dirt and residue are brought in by people entering a facility; a good entrance matting system can trap 90% of this dirt and debris that is brought in!

Prevention is the best defense. It’s important to keep in mind that all floor types are vulnerable during the winter. Using a daily maintenance cleaner is one of the most important steps to extend the life of your floors.

It is important to keep in mind that your floors are vulnerable during the winter. While there is danger afoot due to a combination of increased moisture and salt, remember to practice the above tips to avoid havoc on both carpet and hard surface floors.

HunterGilesRGB
Hunter is the Content Marketing Specialist at Betco.

If you have any questions, please visit http://www.betco.com, call (888) GO-BETCO or please contact us at welisten@betco.com.

floorcare

Floorcare Myths: A higher solids finish is more durable

Floorcare is one of the most challenging cleaning tasks cleaning contractors and facility managers must grapple with. It is time consuming, often stressful, and costly. Complicating matters, several myths have evolved that can make the entire process all the more challenging. One of the biggest myths involves floor finish “solids.”

Usually expressed as a percentage of weight, floor finish solids are whatever is left on the floor after the coating dries and cures. A coating with 50 percent solids, for instance, will be half evaporated after it dries. This means that the higher the solids in the floor finish, the more coating you will have left on the floor after it dries.

These solids are often a blend of several ingredients, each having a specific purpose. These ingredients help the finish resist scuffs, reduce bubbling, improve adhesion and slip resistance, and last but not least, determine overall durability.  Continue reading

iStock_000011885739Small

The Floor Finish is the Foundation

The Floor Finish is the Foundation

It was not that many years ago that property managers, wanting their hard surface floors to have a higher-gloss shine, would ask their jansan distributors and contract cleaners if they could suggest a good “wax” to use on the floor. For more than a century, that was the term used to describe floor finishes, and there was a good reason for it. Many of the early floor polishes were pastes made from leaves of the carnuba plant mixed with other ingredients. These waxes were combined with water to make a liquid paste, which could be buffed using a low-speed machine to clean the floor and produce a reasonably good shine.

Floor Care Maintenance - Sustainable Cleaning Equipment

Polymer emulsion finishes, introduced about 40 years ago, were the first really big advance in floor finishes. These were more durable than waxes, easier to apply to the floor, and usually required little maintenance other than dust and damp mopping. However, over time, the appearance of the floor—specifically the shine—would deteriorate, usually requiring that the floor be stripped and refinished.

Continue reading

iStock_000017624705XLarge

Proper Floor Finish Application

Successfully refinishing a hard surface floor depends a great deal on how the finish is actually applied.

According to Rob Dodson, product manager for Betco® floor care division, “There is a step-by-step process that must be followed when applying floor finish. This helps ensure the finish is properly applied and all areas of the floor are coated.”

Dodson says the process of applying finish starts at the room’s entrance. Here, the technician begins by walking around all four walls of the room, applying finish along the baseboards. “This is often called ‘cutting’ the floor,” says Dodson.

Once this step is complete, the technician makes a 180-degree turn, moves over to the edge of the third wall (furthest from the entrance) and starts applying finish in a back-and-forth “figure-eight” pattern, walking backward.

With this area completed, the technician then turns around and continues applying finish in a back-and-forth pattern, again walking backward, until the next section of the floor is finished. Eventually, the process ends where it started-at the first wall and entrance to the room.

imagesCAZ9RY5G

Continue reading

Don’t Get Backed Into A Corner: Tips For Refinishing Floors

One of the more challenging and time-consuming steps in stripping and refinishing floors is ensuring that the edges and corners are free of finish and dirt buildup.

Look like a professional by taking the extra time to remove all the finish from the edges and corners.

The following process is recommended to make your next strip and recoat look its best:

  1. Make sure you have proper personnel protective equipment such as gloves and safety goggles and set up wet floor signs.
  2. Properly dilute the stripper according to label directions.refinishing floors, floor finish. floor, tile, vct tile, school
  3. Pour the stripper onto the floor and let it sit or dwell for 10 minutes.
  4. Take a razor blade scraper on an extension pole and scrape the edges of the floor along the baseboards or display shelves.
  5. Use a “Doodle Bug” and a black strip pad to remove any excess finish along the edges.
  6. Take a floor squeegee to pull the stripper solution from along the edges onto the center of the aisle.
  7. Pick up solution with an auto scrubber.
  8. Rinse the floor with clean water if necessary.
  9. Apply new floor finish along the edges with the first and final coat. All other coats in between should not go any closer than a few inches of the edge. This will help speed up the removal process next time around.

 

Rob

Rob Dodson
Product Manager, Floor Care, Betco Corporation
rdodson@betco.com

Rob is an avid Cleveland sports fan and hopes to one day experience a championship. He also enjoys hanging out with his wife and 3 kids.

 

 

Summer School – The Time To Clean

The summer months can be some of the busiest and most important months when it comes to school cleaning. To ensure your custodial team is productive summer school and to help simplify the process, share these top ten recommendations.

apple, betco, summer cleaning, cleaning, schools, summer school, go green, education, floor care 1. Prepare a written plan as to who will tackle which projects and when.

2. Divide and conquer. Big summer cleanup projects usually involve floor care; before doing any floor-care work, divide the facility into different categories. Such as those that will be stripped/refinished, those that will only be scrubbed, and those that need only detail cleaning.

3. Clean up those closets. Go through janitorial closets and properly discard any chemicals or other products that have expired. Typically, chemicals should never be stored for more than one year.

4. Go green. Start making the shift to go Green. Special green cleaning training may be required  during this transition, and summer break can provide that extra time.

5. Get Equipped. Evaluate all of your cleaning equipment; determine which machines are running properly, which need servicing, and which should be replaced.

Continue reading

New Product: Express® with SRT

New from Betco Express® with Scuff Resistant Technology™. Betco Express with SRT is a fast drying, fast curing, and extremely low odor floor finish with superior black heel mark resistance. Betco Express with SRT is formulated with Max-Cure™ Technology that utilizes a highly durable, internally cross-linked polymer, specially blended to minimize dry and cure times. This labor savings, one of a kind floor finish can be re-coated in as little as 10-15 minutes allowing up to six coats in one hour.

This new and improved finish will have the same great price and SKU’s! Available August 4th, 2014 for shipment. Click below to watch our new Express with SRT video.

Express with SRT Launch from Betco Corporation on Vimeo.

Floor Finish Myth: A higher solids finish is more durable

Floorcare is one of the most challenging cleaning tasks cleaning contractors and facility managers must grapple with. It is time consuming, often stressful, and for building owners and managers, costly. Complicating matters, several myths have evolved that can make the entire process all the more challenging. One of the biggest myths involves floor finish “solids.”

Usually expressed as a percentage of weight, floor finish solids are whatever is left on the floor after the coating dries and cures. A coating with 50 percent solids, for instance, will be half evaporated after it dries. This means that the higher the solids in the floor finish, the more coating you will have left on the floor after it dries.

Continue reading